About fittings for stainless corrugated pipe

Corrugated Stainless Steel Pipe Fitting

Brass fittings can be classified according to the way they are connected to pipes. For example, fittings are distinguished for butt, socket, saddle, electrofusion and electrofusion welding, compression couplings, fittings for detachable joints on rubber rings, fittings for adhesive joints, fittings for connections.

Differing in design, pipe fittings are the most common: flange sleeves, tees (equal and unequal), bends, corners, transitions, sockets, couplings, metal-polymer brass union nuts and plugs, as well as polymer pipe clamps.

Фитинги для соединения нержавеющих гофрированных труб

Compression fitting of corrugated stainless steel pipe

Today, the most convenient and practical way to connect corrugated pipes is considered to be fastening using crimp fittings.Муфты, фитинги для гофрированной трубы Crimp connection of fittings is used when installing solid and semi-solid pipes.

The Corrugated Tube Fitting Kit includes a silicone gasket, a brass ferrule, a stainless retaining ring, and a union nut for a threaded nipple.

  • Sizes of connecting DN thread fittings: from 1/2 "to 2" inches.
  • Nominal working pressure depending on the fitting size PN: 15-10 bar.
  • Working medium: water, technical liquids, air and gases.
  • Maximum fluid temperature for brass fitting without gasket: +250°C.
  • Maximum fluid temperature for brass fitting with silicone gasket: +150°C
  • The service life of a brass fitting is up to 50 years, and a limit of 30 years for a silicone gasket in fittings.

The tightness of the fitting-corrugated pipe connection is created by compressing the silicone gasket under the pressure of the brass ring when screwing the union nut onto the fitting body.

When assembling the compression fitting, the installers adhere to the following work algorithm: the end of the corrugated pipe is put into the brass fitting with a loosened union nut to the end and then the nut is tightened. The union nut of the fitting is first tightened by hand, as far as possible, then tighten the nut with a wrench until it stops.

The main advantages of connecting corrugated stainless pipes with a compression fitting are simple installation without the use of special equipment and the same simple dismantling if necessary. With just one wrench, a strong connection is created between the fitting and the flexible corrugated pipe.

The connection of corrugated stainless pipes with a compression fitting does not require periodic maintenance, tightening of the union nut due to its specific connection and stainless steel locking plate.

"Komtsentr Strategy" can offer compression brass fittings for corrugated pipes of connecting dimensions: 15 mm * 1/2; 15mm * 3/4; 20 mm * 1/2; 20 mm * 3/4; 20mm * 1; 25mm * 3/4; 25mm * 1; 32 mm * 11/4; 40 mm * 11/2; 50mm * 2 in.

Купить фитинг для гофрированных нержавеющих труб

Corrugated Stainless Steel Pipe Fittings

lavita фитинги для гофрированной трубы
Clutch (М)
Clutch для нержавеющей гофрированной трубы
Clutch (F)
Clutch neptun iws для газа
Clutch (М) dielectric
Clutch neptun iws f для газа
Clutch (F) dielectric
Clutch neptun iws connective для трубы гофрированной
Clutch connective
Clutch neptun iws reduction для гофротруб
Clutch reduction
фитинги для нержавейки гофрированной
Coupling elbow (М)
фитинги для нержавейки гофрированной трубы
Coupling elbow (W)

 

фитинги lavita нержавейка
Coupling tee (F)
Купить фитинги lavita
Coupling tee (M)
фитинг лавита для гофрированной трубы
Tee connecting 3T
Купить фитинг лавита
Reducing tee
фитинг для гофрированных нержавеющих труб
Coupling tee (F) with fastening
кран шаровой для гофротрубы
Ball valve for corrugated pipe
фитинги кран для нержавейки гофрированной
Ball valve for corrugated pipe
накидная гайка для гофрированной нержавейки
Union nut

Corrugated stainless steel pipe fittings

Designations

fittings

Clutch for 15mm corrugated pipe with 1/2" male thread

15*1/2 (М)

Clutch for corrugated pipe 15 mm with 1/2 inch female thread

15*1/2 (F)

Clutch for 15mm corrugated pipe with 3/4" male thread

15*3/4 (М)

Clutch for corrugated pipe 15 mm with 3/4 inch female thread

15*3/4 (F)

Clutch for corrugated pipe 20 mm with 1/2 inch female thread

20*1/2 (F)

Clutch for 20mm corrugated pipe with 1/2 '' male thread

20*1/2 (М)

Clutch for corrugated pipe 20 mm with external thread 3/4 inch

20*3/4 (М)

Clutch for corrugated pipe 20 mm with 3/4 inch female thread

20*3/4 (F)

Clutch for 25mm corrugated pipe with 3/4" male thread

25*3/4 (М)

Clutch for corrugated pipe 25 mm with 3/4 inch female thread

25*3/4 (F)

Clutch for corrugated pipe 25 mm by 1 in. (M) male thread

25*1 (М)

Clutch for corrugated pipe 25 mm by 1 inch (F) female thread

25*1 (F)

Clutch for corrugated pipe 32-11 / 4 (M) male thread

32*11/4 (М)

Clutch for corrugated pipe 32-11 / 4 (F) female thread

32*11/4 (F)

Clutch nickel plated 40-11 / 2 (F) female

40*11/2 (F)

Clutch nickel plated 40-11 / 2 (M) male thread

40*11/2 (М)

Clutch nickel plated 50-2 "(F) female thread

50*2" (F)

Clutch Nickel Plated 50-2 "(M) Male Thread

50*2" (М)

Clutch "pipe - male" for gas G-V / S 15-1 / 2

GV/S15*1/2(М)

Clutch "pipe - female" for gas G-V / S 15-1 / 2 (F)

GV/S15*1/2(F)

Clutch "pipe - male thread" for gas G-V / S 20-3 / 4

G-V/S20*3/4(M)

Clutch "pipe - female" for gas G-V / S 20-3 / 4 (F)

G-V/S20*3/4(F)

Clutch "pipe - male" for gas G-V / S 25-1

G-V/S 25*1(M)

Clutch pipe-female for gas G-V / S 25-1 (F)

G-V/S 25*1(F)

Clutch angle - female thread E / S 15-1 / 2

E/S 15*1/2(F)

Clutch angle - external thread E / S 15-1 / 2 (M)

E/S 15*1/2(M)

Clutch angle - female thread with fastening E / S 15-1 / 2 (W)

E/S 15*1/2(W)

Clutch angle - female thread E / S 20-3 / 4

E/S 20*3/4(F)

Clutch angle - external thread E / S 20-3 / 4 (M)

E/S 20*3/4(M)

Clutch angle - female thread with fastening E / S 20-3 / 4 (W)

E/S 20*3/4(W)

Clutch angle - female thread E / S 25-1

E/S 25*1(F)

Tee pipe - pipe - pipe 3T 15-15-15

3T 15*15*15

Tee pipe - pipe - pipe 3T 20-20-20

3T 20*20*20

Pipe-pipe-pipe tee 3T 20-15-20

3T 20*15*20

Tee pipe - pipe - pipe 3T 25-25-25

3T 25*25*25

Pipe-pipe-pipe tee 3T 25-20-25

3T 25*20*25

Pipe-pipe-pipe tee 3T 25-15-25

3T 25*15*25

Pipe-pipe-pipe tee 3Т 32-20-32

3Т 32*20*32

Tee pipe - male thread - pipe T/S 15-1/2-15(М)

T/S 15*1/2*15(М)

Tee "pipe - female thread - pipe" T/S 15-1/2-15


Tee pipe - female thread - pipe T/S 20-1/2-20


Tee pipe - male thread - pipe T/S 20-3/4-2(М)


Tee pipe - female thread - pipe T/S 20-3/4-20


Tee pipe - female thread - pipe T/S 25-1/2-25


Tee pipe - female thread - pipe T/S 25-3/4-25


Tee pipe - female thread - pipe T/S 25-1-25


Tee pipe - female thread - pipe T/S 32-1/2-32


Tee pipe - female thread - pipe T/S 32-3/4-32


Tee pipe - female thread - pipe T/S 32-1"-32


Tee pipe - female thread - pipe T/S 32-11/4-32


Tee "pipe-female thread-pipe" with fastening (with ears) T/S 15-1/2-15(W)


Connective clutch pipe-pipe С/Р 15-15


Connective clutch pipe-pipe С/Р 20-20


Connective clutch pipe-pipe С/Р 25-25


Connective clutch pipe-pipe С/Р 32-32


Connective clutch pipe-pipe С/Р 50-50


Connective clutch with tube-tube reduction С/Р 20-15


Connective clutch with tube-tube reduction С/Р 25-15


Connective clutch with tube-tube reduction С/Р 25-20


Silicone gaskets for brass fittings for corrugated pipes  

thanks